Balace Shaft, Motor & Wheel Bearing
Price: $7.80

Part Number: BE125

OEM Part Numbers - HD 30150-67, 90004-90, CC 1011290, 1012877, EZ 16918-G1, 23520-G1, 27630-G13, JA 343667, TD 80-201-00, TO 251-6, CU 812009, 824753, 832498, YA 93306-20304, 93306-20309, 93306-20310, 93306-20314, 93306-20316, 93306-20324, 93306-20331, 93306-20345, 903306-203X1, J56-H1857-00-00, HY GB1-801003

Item Description -
Balancer Shaft Bearing on 1995 and newer Club Car 4 cycle, also 1984 to 1991 Club Car gas balancer shaft clutch side, camshaft flywheel side and electric motor brush end from 1981 and newer (except IQ system), E-Z-GO electric motor brush end on 1980 to 1996, also Jacobsen, Taylor Dunn, Toro, Cushman, also Yamaha front outer wheel bearing for G1 from 1978 to 1981 and electric motor brush end on 1990 and newer G8, G9, G14, G16, G19 and G20, Also Hyundai. Dimensions: .66" (16.8mm) I.D. by 1.57" (39.9mm) O.D. by .47" (11.9mm) W.

Bearing, Crankcase, Axle, Wheel, & Motor
Price: $16.77

Part Number: BE126

OEM Part Numbers - HD 9030, 9034, 72381-72, 83269-79, EZ 15488-G1, 51320-G1, CU 605636, 808058, 821291, 823011, 824703, 835011, YA 93306-20401, 93306-20417, 93306-20420, 93306-20421, 93306-20437, 93306-20469, 93306-204X0, J10-81856-10 TD 80-200-00, DA 56226, JA 315947, ND 20383

Item Description -
Crankcase Bearing for 1963 to 1981 Harley Davidson, for clutch and flywheel side, also 1983 and newer outer front wheel bearing on 4 wheel Harley, E-Z-GO motor bearing, Cushman rear axle bearing, Outer Wheel Bearing for 1982 to 2002 Yamaha models G1, G2, G8, G9, G14, G16, G20, G21, and electric front wheel inner G22, also Electric Motor Bearing for brush end on 1978 to 1991 models G1 and G2 and 1981 to 1984 Club Car both with Hitachi 10 internal spline motor, also for 1979 to 1982 Harley with Hitachi motor., In addition rear axle bearing on Taylor Dunn, Davis, Jacobsen, and Nordskog NOTE: Club Car used this bearing on the front wheel in 2003 on electric carts after serial number AQ344-343603 and on gas carts after serial number AG0343-342005. Dimensions: .78" (19.9mm) I.D. by 1.85" (47mm) O.D. by .5" (14mm) wide.

Brush Assembly
Price: $62.40

Part Number: BR100

OEM Part Numbers - HD 83283-86, CC 1011410, 1011282, ME 520108, CU 886026, TD 70-104-00, LE 5561-2, ND 20953, HY GB1-801062

Item Description -
Brush Assemblies for GE motors used on 1986 to 1990 Harley-Davidson, Club Car 1980 to 1993 36 volt, Melex 1985 and newer models 412, 512, and 625, Cushman, Taylor Dunn, Legend, Nordskog and Hyundai. length 1-7/16" long, 5/8" wide, 1/2"deep. Set includes two assemblies.

Brush Set
Price: $58.55

Part Number: BR101

OEM Part Numbers - HD 70491-73, CC 7363, EZ 15634-G1, 51318-G1, CU 882960, 883663, TD 70-101-00, ND 20753, PA 2227-3, NO M-14, OT A-56224

Item Description -
Brush Set for GE Motors used on Harley Davidson model DE3 from 1977 to 1978 and model DE40 from 1976 to 1978, Club Car 1976 to 1980, E-Z-GO 1973 to 1979, HMK Marketeer models 438 and 439 and model 450 4-Runner, Cushman, Taylor Dunn, Nordskog, Pargo, Noland and Otis .(set of 4), length 1-3/16" long by 5/8" wide by 1/2" thick.

Brush Set
Price: $39.37

Part Number: BR102

OEM Part Numbers - HD 70491-63, 72367-72, CC 7363, 8089, 8785, EZ 50278-G1, 72368-G01, CU 807329, 824251, 882960, TD 70-100-00, ME 500117, PA 3365-3, OT A-20663, WE 20663, A2623A54H02, A2623A54H03

Item Description -
Brush set for GE Motors used on 1963 to 1971 Harley Davidson models DE, DEF, DEC and 1972 to 1975 models DE and DE4, Club Car pre 1980, E-Z-GO 1965 to 1972, also Cushman, Taylor Dunn, Melex pre 1985 models 102, 202, 112, 212, 152, 252, and early 412 with band brake on motor, also Pargo as well as Westinghouse Motors used on 1965 to 1976 Westinghouse Marketeer models 436, 436G, 437 and 437A, and 529 Chariot, also Otis, Nordskog and others using Westinghouse motors (set of 4), length 1-5/8" long, 5/8" wide, 1/2" deep with spring hook. NOTE: Used with both GE and Westinghouse motors

Brush, Traction Motor Set
Price: $46.80

Part Number: BR103

OEM Part Numbers - HD 82918-79, CC 1011332, 1011424, YA J14-81811-10,

Item Description -
Brush Set for late 1979 to 1982 Harley Davidson model DE3 with Hitachi Motor only, also Club Car 1980 to 1984, and Yamaha G1 and G2 . (set of 4), length 1-1/8"long, 11/16" wide, 5/8"deep.

Brush Spring
Price: $2.40

Part Number: BR104

OEM Part Numbers - HD 83287-86, CC 1011411, EZ 15446-G1, CU 824754, TD 85-412-00, DA 56225, LE 2227-5, NO M-12, ND 10556, OT A-56225, PA 2227-5

Item Description -
Brush Spring for G.E. Motor used by Columbia/Harley-Davidson, Club Car 1984 and newer, E-Z-GO new style G.E. motor, HMK Marketeer models 438 and 439, Melex 1985 and newer models 412, 512, and 625, also Cushman motor brush spring and speed board brush spring, Taylor Dunn, Davis, Legend, Noland, Nordskog, Otis, Pargo, and Yamaha G8, G9, G14, G16.

Brush Spring
Price: $8.37

Part Number: BR105

OEM Part Numbers - HD 72383-66, EZ 50280-G1, CU 814289, TD 85-401-00, ME 500115, ND 20433, PA 3365-5

Item Description -
Pull Type Brush Spring for GE Motors used on 1963 to 1971 Harley Davidson models DE, DEF, DEC and 1972 to 1973 models DE and DE4, also E-Z-GO, Club Car pre 1980, Cushman, Taylor Dunn, Melex pre 1985 models 102, 202, 112, 212, 152, 252, and early 412 with band brake on motor, Also Westinghouse Marketeer models 436, 436G, 437 and 437A and 529 Chariot, and Nordskog, and Pargo .

Brush Spring
Price: $7.02

Part Number: BR106

OEM Part Numbers - HD 82919-79, CC 1011420, YA J14-81813-10

Item Description -
Brush Spring for late 1979 to 1982 Harley Davidson model DE3 and MGIV, with Hitachi Motor only, also Club Car 1980 to 1984 and Yamaha G1 and G2 with Hitachi Motor

Brush Set
Price: $39.23

Part Number: BR107

OEM Part Numbers - HD 70491-73, 82842-86, CC 7363, EZ 15445-G1, 15634-G1, PA 2227-3, TD 70-105-00, NR 20753, DA 56224

Item Description -
Brush Set for GE Motors with cable lead crossovers used on Harley Davidson from 1986 to 1990, Club Car 1981 to 1985, HMK Marketeer from 1976 to 1977 models 438 and 439 and model 450 4-Runner, also E-Z-GO, Pargo, Taylor Dunn, Nordskog and Davis.(set of 4), length 1-7/16" long by 5/8" wide by 1/2" thick. NOTE: similar to BR101 except this brush has a groove in the top for the brush spring

Brush Holder with Springs
Price: $87.79

Part Number: BR116

OEM Part Numbers - HD 82916-79, 82919-79, CC 1011326, 1011420, YA J14-81813-10

Item Description -
Brush Holder with Springs for late 1979 to 1982 Harley Davidson model DE3 and MGIV with Hitachi Motor only, also Club Car 1981 to 1984, and 1978 to 1991 Yamaha G1 and G2.

Brush Holder
Price: $62.40

Part Number: BR205

OEM Part Numbers -EZ 16916-G1, 16916-G2, CC 1011284, HD 83284-86, LE 5561-1
Item Description -
Brush Holder with Springs for 1980 to 1992 E-Z-GO with G.E. Motor, Club Car 1984 to 1993 36 volt, Columbia Harley 1986 to 1990, and Legend

BR206
Price: $68.25

Part Number: BR206

OEM Part Numbers - EZ 27630-G05, CC 1017946, ME 520108, YA JH7-H1801-00 GE Motor #s 5BC48JB868, 5BC48JB882, 5BC58JBS6259

Item Description -
Brush Set with Hex Stud for 19 Spline, 2 HP, 2800 RPM G.E. 36 Volt Fleet Speed Motor style JBS, our part number MT209, for 1988 and newer E-Z-GO non DCS and PDS, 1994 and newer Club Car, also 1990 to 2002 Yamaha G8, G9, G14 and G16, and Melex model 412 and later without brake on motor, also Hyundai with 19 spline, Dimensions: 1-3/8" long by 5/8" wide by 1/2" thick

Field Coil Repair Stud
Price: $5.45

Part Number: MT110

OEM Part Numbers -

Item Description -
Copper Field Coil Repair Stud with square shoulder for Harley Davidson, E-Z-GO, Club Car, and many others with GE Motor, 5/16"-18 by 1-1/2" long

Repair Stud, Screw On
Price: $5.99

Part Number: MT111

OEM Part Numbers -

Item Description -
Screw On Motor Repair Stud for repairing broken field coil studs on GE Motors, 5/16" by 18 coarse thread

Fiber Washer
Price: $2.45

Part Number: MT112

OEM Part Numbers -HD 83260-75, 83289-86, CU 823015, 824710, EZ 15442-G1, 50309-G1, 51330-G1, DA 56236, NO M-13, PA 2227-11, ND 70621, 70771

Item Description -
Round Fiber Washer for old style GE Motors used on Harley Davidson, Cushman, E-Z-GO, Davis, Noland, Pargo, Nordskog and others, has .475 hole, goes on inside where stud field stud or brush stud goes through the brush housing

Fiber Washer
Price: $2.85

Part Number: MT113

OEM Part Numbers -HD 83256-75, 83288-86, CU 814316, 824718, EZ 15438-G1, 50289-G1, 51327-G1, DA 56233, NO M-6, LE 2227-38, ND 70611, PA 2227-13, 3365-13

Item Description -
Round Fiber Washer for old style GE Motors used on Harley Davidson, Club Car, Cushman, E-Z-GO, Davis, Noland, Otis, Legend, Taylor Dunn and Pargo and others, has .330 hole, goes on outside where field stud or brush stud goes through the brush housing

Motor Insulating Bushing Kit
Price: $11.70

Part Number: MT117

OEM Part Numbers -HD 82837-86, CC 1011407, CU 824711, EZ 15437-G1, DA 56232, LE 2227-37, NO M-4

Item Description -
G.E. Motor Insulating Bushing Kit for G.E. Motor with Square Insulating Bushing which is .227" thick with .335" hole for old style GE Motors used on Harley Davidson, 1984 to 1993 Club Car, Cushman, E-Z-GO, Davis, Noland, and others, Includes the plastic square bushing, two fiber washers, one with a .330" hole and the other with a .475" hole plus one 5/16" steel washer and one 5/16" serrated nut.

Nut & Washer Kit, Motor Terminal Stud,
Price: $13.75

Part Number: MT120

OEM Part Numbers - HD 83273-79, YA 95333-08600-00, 92990-08100-00, 92990-08200-00

Item Description -
Nut and Washer Kit for Motor Stud on late 1979 to 1982 Harley Davidson model DE3 and MGIV with Hitachi Motor only, also Club Car 1980 to 1984, and Yamaha G1, Includes four serrated lock washers, four split lock washers, eight flat washers, and eight 8mm by 1.25 thin brass nuts.

Motor Coupler, 10 Spline
Price: $43.68

Part Number: MT215

OEM Part Numbers - 26926-G01

Item Description -
10 Spline Motor Coupler for repairing stripped splines on E-Z-GO from 1971 to 1985 and Club Car 1981 to 1985

16 Spine Motor
Price: $658.45

Part Number: MT402

OEM Part Numbers - CC 7260, 7448, PA 3365, 2227, GE 5BC48JB719, 5BC48JB722, 5BC48JB524, 5BC48JB558B, 5BC48JB691, Hitachi MT320-07

Item Description -
16 External Spine, 36 Volt 2.90 HP, 2475 RPM Replacement Motor for 1976 to 1983 Club Car with Terrill differential, also 1969 and newer Pargo with Terrill differential with disc brake on differential, in addition 1960s E-Z-GO with 16 Spline Motor, Also replaces Hitachi motor on early Yamaha GI with external shaft motor. NOTE: This motor has slightly more horsepower than the original motor.

16 Spline Motor, (Used)
Price: $365.00

Part Number: MT402B

OEM Part Numbers - CC 7260, 7448, PA 3365, 2227, GE 5BC48JB261, 5BC48JB524, 5BC48JB558B, 5BC48JB691, 5BC48JB719, 5BC48JB722, Hitachi MT320-07

Item Description -
Good Used Stock 16 External Spine General Electric, 36 Volt, 2800 RPM Motor for 1976 to 1983 Club Car with Terrill differential, also 1969 and newer Pargo with Terrill differential with disc brake on differential, in addition 1960s E-Z-GO with 16 Spline Motor, Also replaces Hitachi motor on early Yamaha GI with external shaft motor. NOTE: This particular motor was manufactured in April of 1971. I personally checked this motor out.

High Speed Motor
Price: $674.32

Part Number: MT403

OEM Part Numbers - 7260, 7448

Item Description -
High Speed 16 External Spine 3850 RPM, 36 Volt High Speed Replacement Motor for 1976 to 1983 Club Car with Terrill differential, also 1969 and newer Pargo with Terrill differential with disc brake on differential, in addition 1960s E-Z-GO with 16 Spline Motor, Also replaces Hitachi motor on early Yamaha GI with external shaft motor. On 36 volts it will increase speed from 12 mph to 16-17.5 mph. If run on 48 volts it will increase speed to 20-22 mph. NOTE: You must either retrofit to 400 amp controller and 200 amp solenoid and heavier wires or upgrade all solenoids to 200 amp units and install heavier wiring

10 Spline Motor
Price: $516.75

Part Number: MT405

OEM Part Numbers - CC 1012643, 1012653, 1014678, 1017728-01, 1017728-02, 1018134-01, 1018134-02, 1022374-01, YA JG6-H1890-00, JG6-H1890-01

Item Description -
10 Spine 36 Volt Upgrade Replacement Motor for 1984 and newer Club Car and and Yamaha 1989 to 1993-1/2 G1, G2, G8, and G9 with Graziano or Kawasaki Differentials. 3.5 HP @ 3000 RPMs. NOTE: Not for use with Club Car PowerDrive Plus systems

High Speed 10 Spline Motor
Price: $627.50

Part Number: MT406

OEM Part Numbers - CC 1012643, 1012653, 1014678, 1017728-02, 1018134-01, 1018134-02, 1022374-01, YA JG6-H1890-00, JG6-H1890-01, GE 5BC49JB3071

Item Description -
10 Spine High Speed Motor for 1984 and newer Club Car and Yamaha 1989 to 1993-1/2 G1, G2, G8, and G9 with Graziano or Kawasaki Differentials, 4 horsepower at 36 Volts and 4150 RPMs, 5.5 horsepower at 48 Volts and 5700 RPMs, will replace above OEM Club Car part numbers, This motor works best at 48 volts having a good combination of torque and speed. At 48 volts it will do 25 mph. NOTE: at 48 Volts you will need a 400 amp or larger controller. It is also highly recommended to run heavy duty cables and a heavy duty forward and reverse switch our part number FR410. NOTE: Not for use with Club Car PowerDrive Plus systems. Will do speeds up to 25 MPH. Weight: 52 pounds.

High Speed 36 Volt Motor
Price: $597.49

Part Number: MT407

OEM Part Numbers - CC 1012643, 1012653, 1014678, 1017728-02, 1018134-01, 1018134-02, 1022374-01, YA JG6-H1890-00, JG6-H1890-01

Item Description -
10 Spine 36 Volt High Speed Motor for 1984 and newer Club Car and Yamaha 1989 to 1993-1/2 G1, G2, G8, and G9 with Graziano or Kawasaki Differentials. 6.1 HP @ 4600 RPMs. Speeds up to 25 MPH on 36 volts. NOTE: Must use 400 amp or higher controller. NOTE: Not for use with Club Car PowerDrive Plus systems. NOTE will replace OEM part numbers above. Important Note: This low torque high speed motor is not suitable for lifted carts. Also best used where there art not a lot of hills

10 Spline 48 Volt Motor
Price: $574.49

Part Number: MT408

OEM Part Numbers - CC 1017857-04

Item Description -
High speed 10 Spine 48 Volt Upgrade Replacement Motor for 1995 and newer 48 Volt Series Club Car. 3.75 HP @ 3150 RPMs. Will increase speed up to 19 MPH with an increase in torque. NOTE: You must use a 350 amp or larger controller. NOTE: Not for use with Club Car PowerDrive Plus systems

High Speed 36/48 Volt Motor
Price: $563.32

Part Number: MT409

OEM Part Numbers -

Item Description -
10 Spine High Speed Upgrade Replacement Motor for 1984 and newer Club Car and 1996 and newer 48 volt Club Cars with series system. Also Yamaha 1989 to 1993-1/2 G1, G2, G8, and G9 with Graziano or Kawasaki Differentials. 4 HP @ 3000 RPMs at 36 volts and 5.3 HP at 48 volts at 4000 RPMs. NOTE: Not for use with Club Car PowerDrive Plus systems

High Torque Motor
Price: $697.95

Part Number: MT410

OEM Part Numbers - GE 5BC48JB1134

Item Description -
Very High Torque 10 Spine 36 and 48 Volt Motor for 1984 and newer Club Car and 1989 to 1993-1/2 Yamaha G1, G2, G8, and G9 with Graziano or Kawasaki Differentials. 8 HP @ 1600 RPMs at 36 volts and 11 HP @ 2300 RPMs at 48 volts. NOTE: This is a very high torque motor recommended for hilly areas and lifted carts eith larger tires. Speeds up to 15 MPH on 36 volts and 18 MPH on 48 volts with stock tires. Larger tires will increase speed. NOTE: Must use 400 amp or higher controller and upgrade to 4 gauge wires. NOTE: Not for use with Club Car PowerDrive Plus systems.